Operation Water Pollution

Operation Water Pollution enables students in grades five to twelve to learn about water pollution (including what causes it, how it is cleaned up, how it can be prevented, and what they can personally do about the problem). The Operation Water Pollution program directly connects with science and social studies curricula.

Generally, sponsored Operation Water Pollution kits are sent to schools every Monday during the school year. Purchased kits are usually sent on the same dates, but teachers can request that they be sent as soon as possible and we will do our best to accommodate their request.

Notes to teachers from Tracy Webb, Science Teacher and Member of the SDWF Board of Directors:

The 12 lessons in the Operation Water Pollution program represent a comprehensive unit on water issues. Each lesson generally builds on the previous one and includes relevant, up-to-date, and well-researched fact sheets and background information. However, teachers may use any lesson on its own, or any combination, understanding that they may need to add some of the background information provided in other lessons. Every lesson can be further modified or enriched for the age and abilities of students, from grades 5 to 12. Lessons may be easily changed to reflect local conditions and situations as well, especially if teachers are/become aware and informed about their own area's water issues.

For the experimental activities, teachers may wish to substitute according to their own available supplies and/or approach to the lesson. Quantities suggested in the lesson may also be adapted as determined by the teacher.

Every lesson includes additional suggested activities and resources, along with references to other sources of information.

Cost

For lessons five and six you will need a digital TDS meter and a digital pH meter. These digital meters are included in Operation Water Pollution kits, which are available from the Safe Drinking Water Foundation.

The cost of an OWP kit is $170 and includes both a digital TDS and a digital pH meter. It should be noted that each meter is guaranteed to be reusable for at least two years. Many school kits are available free of charge as a result of different sponsors. However, if there is not a sponsored kit available for your school or you want a kit right away it is best to purchase a kit.

Or, phone us at 1-306-934-0389 to pay for your kit with Visa or MasterCard.

Or, mail a cheque payable to Safe Drinking Water Foundation to:
Safe Drinking Water Foundation
#1-912 Idylwyld Drive North
Saskatoon, SK S7L 0Z6

Important Notes about the TDS Meter:

To use the TDS meter, immerse the meter into the water/solution up to the max. immersion level (2"), lightly stir the meter to dislodge any air bubbles. Wait until the display stabilizes. Once the reading stabilizes (approximately 10 seconds), press the HOLD button to view the reading out of the water. After usage, shake off any excess water from your meter and make sure to turn the meter off to preserve battery power.

Note that if the TDS is 1000 or higher there will be a flashing 'x10' symbol, multiply the reading by 10.

Important Notes about the pH Meter:

Your PH-80's sensor must be wetted in the electrode storage solution for at least 15 minutes prior to use. The solution is inside the large Mylar packet (included). Simply pour this solution into the cap, so that the sponge is moist. Excess solution can be poured out. Insert the meter into the cap and stand upright for 15 minutes.

The smaller Mylar packet contains a 7.0 buffer powder to be used for calibration. Mix the contents of the packet with 100 mL of distilled water. When stored in a sealed container, the solution will last approximately 2-4 weeks. Additional pH buffers and storage solution can be purchased from gardening and science stores, as well as major online retailers. Your meter was factory calibrated to pH 7.0 as a convenience for your first few uses. Calibrate your meter at least once per month. When taking the pH measurement, lightly swirl the meter to ensure the removal of air bubbles or electric charges. The meter will display a reading almost instantly. Keep the meter in the water until the reading stabilizes (up to 30 seconds). To view the reading out of the liquid, click the HOLD button. This will freeze the reading on the screen. Clicking HOLD again will release it. After using the meter, make sure to turn the meter off to preserve battery power, and shake off any excess water and rinse with low TDS water (such as distilled or reverse osmosis).

Both the pH meter and the TDS meter also measure temperature. To learn more about water temperature and how it affects the water and its treatment please read our Water Temperature Fact Sheet.

Overview materials

LESSON 1: Lesson and related resources

LESSON 2: LESSON AND RELATED RESOURCES

LESSON 3: LESSON AND RELATED RESOURCES

LESSON 4: LESSON AND RELATED RESOURCES (The digital meters in the operation water pollution kit are helpful for this lesson)

Lesson 5: Lesson and Related Resources (The digital meters in the operation water pollution kit are used in this lesson)

Lesson 6: Lesson and Related Resources (The digital meters in the operation water pollution kit are used in this lesson)

Lesson 7: Lesson and Related Resources

Lesson 8: Lesson and Related Resources

Lesson 9

Lesson 10: Lesson and Related Resources

Lesson 11

LESSON 12

Crapshoot Film, Lessons and Resources